A Journey of Thousand Miles Begins With Single Step

Fire All Dual Fuel Burner 2514

Fire All Dual Fuel Burner 2514
2514 Fire All Heavy Oil Burners are rugged, maintenance free, intact burners for burning light or heavy oil on a wide applications. Capable of efficient operation throughout a wide temperature range, they are equally at home on
low temperature ovens and high temperatures forge and melt furnaces
. Sealed mountings help maintain furnace pressure, controlled atmosphere, and closer fuel/air ratio control--all contributing to better product quality. Fire All Burners have been used for yearswith great success on all types of furnaces.

Combustion Performance
2514 Burners are better with 200% or more excess air. They may also be operated with excess fuel without forming carbon if additional combustion air is available in the furnace near the burner. Excess fuel limit with heavy oil is 50%as atomization deteriorates at richer ratios.
Burners can be turned down to atomizing air only, but stability limits vary depending on burner size, grade of oil, and furnace atmosphere. For prolonged operation on atomizing air only in furnaces over 1200oC specify an alloy burner nose.
Burners are suitable for some preheated combustion air applications (up to 350oC). Oil viscosity at the burners should not exceed 90 seconds R.W.1; oil pressure at the Ratio controller should be between 25 and 30psi. Minimum atomizing air pressure at the burner is 24”wg for light oil, 42”wg for heavy oil

Air Capacities (Including Main and Atomizing Air)
Burner Designation 28"wg air pressuredrop across burner 44”wg air pressure drop across burner
  Air-cfh Oil-lph Air-cfh Oil-lph
2514-6A 17 900 52 21 900 63
2514-7A 28 400 79 34 800 99
2514-8AA 48 900 139 60 000 171
2514-9AA 81 500 230 100 000 282
2514-10A 165 000 468 102 000 572
2514-11A 247 000 698 303 000 857
Working Nature
Control: Normally, air primary with a cross-connected, pressure balance regulator. For maximum turndown, use a (biased) Regulator, or throttle gas only. To protect burner from heat damage, do not set air pressure below 2”wg in a 850oC furnace, or below 3”wg at 1000oC (whether gas is on or off). Gas pressure requirement: About 2”wg at the burner for natural gas on stoichiometric ratio; about 1/5 of the air pressure for coke oven gas. Preheated air: 2514 Burners are suitable for some applications with air preheated to 400oC.

Burner Block/Installation. Burner Blocks are cast refractory rated for 1450oC furnace temperature. They should be supported securely in the furnace wall by a layer of castable refractory at least 9" thick all around the Burner Block, extending back to the furnace shell and securely anchored to it. Burner Blocks are replaceable in the field except for the 2514-10A, whose mounting must be returned to the factory for Burner Blocks replacement. The 10A size is also available with a short Burner Blocks that extends 2" past the mounting plate. The remaining Burner Block length is then field constructed. For furnace walls thicker than the length of the Burner Block, tunnel beyond the end of the Burner Blocks should be flared at least 30°, starting at the OD of the Burner Block. If this is not practical, consult ATEC Experts for specific recommendations.

Jacketed Burner Blocks. 2514 Burners are available with support jackets around the Burner Blocks for applications where the Burner Blocks is not supported by furnace refractory. Jackets are available in three different metals and have maximum temperature ratings for each. They must be protected with sufficient insulation so as not to exceed rated temperature. Maximum temperature rating for jacket metals depends upon frequency of heat-up/cool-down
cycles. As an example, batch annealing furnaces that are heated and cooled every day should use the "intermittent exposure" ratings. Continuous annealing furnaces that remain at the same temperature for months at a time, can use the higher "continuous" rating.

Designation Jacket Metal Continuous max.temp Intermittent exposure
2514- AS carbon steel 400O C 400O C
2514- A1 304 SS 850 O C 750 O C
2514- A2 309 SS 1100O C 1050OC
Complete burners include Burner Block, mounting plate, precise oil control valve and an observation port into which a small quantity of atomizing air is introduced to keep the glass clear. Order pilot tips separately.
Enquiry

Other Products
  • Fire All Gas Burner 1514
  • High Velocity Gas Burner 1435
  • Gas Burner 1562
  • HF Burner 001
  • Excess Air Light Oil Burner 2422
  • Fire All Heavy Oil Burner 2514
  • Furnace Oil Burner 2562
  • HF Burner 002
  • High Velocity Oil Burner 2435
  • Excess Air fuel/Gas Burner 3422
  • Fire All Dual Fuel Burner 3514
  • Dual Fuel High Velocity Burner 3435
  • Dual Fuel Burner 3562
  • HF Burner 003
NOTE : Dimensions shown are subject to change. please obtain certified prints from Axis Thermal Engineering Company. If space limitations or other considerations make exact dimension(s) critical.
WARNING: Situations dangerous to personnel and property can develop from incorrect operation of combustion equipment. Axis Thermal urges compliance with National Safety Standards and Insurance Underwriters recommendations, and care in operation.